yaffs移植不成功

       我用的2440，256M，4.3寸屏的开发板，交叉编译环境用的4.3.3。
       我按Linux移植手册4.5，编译了linux-2.6.30.4内核，配置单是直接导入的天嵌配套的，并添加了其对yaffs文件系统的支持，随后又制作了yaffs文件镜像，烧入开发板后串口显示信息如下。
       （1）用天嵌的zImage_Q43_2.6.30.4_20100531.bin + 我自己的yaffs文件镜像也不行，显示的是同样的串口信息。
       （2）用自己的内核镜像 + 天嵌的root_qtopia_2.2.0_2.6.30.4_256MB_20100601.bin，一切正常。
       （3）用天嵌的zImage_Q43_2.6.30.4_20100531.bin + 天嵌的root_qtopia_2.2.0_2.6.30.4_256MB_20100601.bin，也一切正常。
        我感觉应该是yaffs文件镜像不对，我用的是busybox-1.16.0，文件系统中的内容我自己按照手册做了一遍不行，又直接添加天嵌制作好的文件系统重做了一遍，还是不行。
       到底是哪个地方出了问题呢？请教大家了，谢谢了！
       串口信息如下，并且开发板会不断重新启动。

串口信息如下：
##### EmbedSky BIOS for SKY2440/TQ2440 #####
Press Space key to Download Mode !
Booting Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00300000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
Uncompressing Linux......................................................................................................................................................... done, booting the kernel.
Linux version 2.6.30.4-EmbedSky (root@EmbedSky) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #8 Mon May 31 10:57:52 CST 2010
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: TQ2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
NR_IRQS:85
irq: clearing pending ext status 00080000
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 59860KB available (4320K code, 448K data, 240K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 296 bytes
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 97 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
yaffs May 31 2010 10:39:00 Installing.
msgmni has been set to 117
alg: No test for stdrng (krng)
io scheduler noop registered (default)
Console: switching to colour frame buffer device 60x17
fb0: s3c2410fb frame buffer device
backlight initialized
GPIO-Control initialized
PWM-Test initialized
adc initialized
s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
dm9000 Ethernet Driver, V1.31
Now use the default MAC address: 10:23:45:67:89:ab
eth0 (dm9000): not using net_device_ops yet
eth0: dm9000e at c4814000,c4818004 IRQ 51 MAC: 10:23:45:67:89:ab (EmbedSky)
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 192 at 0x000001800000
Bad eraseblock 193 at 0x000001820000
Bad eraseblock 252 at 0x000001f80000
Bad eraseblock 254 at 0x000001fc0000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000500000 : "EmbedSky_Board_kernel"
0x000000500000-0x000010000000 : "EmbedSky_Board_yaffs2"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.30.4-EmbedSky ohci_hcd
usb usb1: SerialNumber: s3c24xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
s3c2410_udc: debugfs dir creation failed -19
s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
mice: PS/2 mouse device common for all mice
TQ2440 TouchScreen successfully loaded
input: TQ2440 TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
cx231xx v4l2 driver loaded.
usbcore: registered new interface driver cx231xx
usbcore: registered new interface driver usbvision
USBVision USB Video Device Driver for Linux : 0.9.10
usbcore: registered new interface driver ov511
ov511: v1.64 for Linux 2.5:ov511 USB Camera Driver
SE401 usb camera driver version 0.24 registering
usbcore: registered new interface driver se401
usbcore: registered new interface driver stv680
stv680 [usb_stv680_init:1550]
STV(i): usb camera driver version v0.25 registering<6>stv680: v0.25:STV0680 USB Camera Driver
w9968cf: V4L driver for W996[87]CF JPEG USB Dual Mode Camera Chip 1:1.34-basic
usbcore: registered new interface driver w9968cf
usbcore: registered new interface driver zr364xx
zr364xx: Zoran 364xx
usbcore: registered new interface driver stkwebcam
sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.47pre49
usbcore: registered new interface driver sn9c102
et61x251: V4L2 driver for ET61X[12]51 PC Camera Controllers v1:1.09
usbcore: registered new interface driver et61x251
pwc: Philips webcam module version 10.0.13 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
usbcore: registered new interface driver Philips webcam
zc0301: V4L2 driver for ZC0301[P] Image Processor and Control Chip v1:1.10
usbcore: registered new interface driver zc0301
gspca: main v2.5.0 registered
usbcore: registered new interface driver conex
conex: registered
usbcore: registered new interface driver etoms
etoms: registered
usbcore: registered new interface driver finepix
finepix: registered
usbcore: registered new interface driver mars
mars: registered
usbcore: registered new interface driver mr97310a
mr97310a: registered
usbcore: registered new interface driver ov519
ov519: registered
usbcore: registered new interface driver ov534
ov534: registered
usbcore: registered new interface driver pac207
pac207: registered
usbcore: registered new interface driver pac7311
pac7311: registered
usbcore: registered new interface driver sonixb
sonixb: registered
usbcore: registered new interface driver sonixj
sonixj: registered
usbcore: registered new interface driver spca500
spca500: registered
usbcore: registered new interface driver spca501
spca501: registered
usbcore: registered new interface driver spca505
spca505: registered
usbcore: registered new interface driver spca506
spca506: registered
usbcore: registered new interface driver spca508
spca508: registered
usbcore: registered new interface driver spca561
spca561: registered
usbcore: registered new interface driver sq905
sq905: registered
usbcore: registered new interface driver sq905c

续上：
sq905c: registered
usbcore: registered new interface driver sunplus
sunplus: registered
usbcore: registered new interface driver stk014
stk014: registered
usbcore: registered new interface driver t613
t613: registered
usbcore: registered new interface driver tv8532
tv8532: registered
usbcore: registered new interface driver vc032x
vc032x: registered
usbcore: registered new interface driver zc3xx
zc3xx: registered
usbcore: registered new interface driver ALi m5602
ALi m5602: registered
usbcore: registered new interface driver STV06xx
STV06xx: registered
usbcore: registered new interface driver ibmcam
usbcore: registered new interface driver ultracam
konicawc: v1.4:Konica Webcam driver
usbcore: registered new interface driver konicawc
usbcore: registered new interface driver vicam
quickcam_messenger: v0.01:Logitech Quickcam Messenger USB
usbcore: registered new interface driver QCM
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: starting watchdog timer
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: powered down.
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
ALSA device list:
  #0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2009-01-02 11:22:41 UTC (1230895361)
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
block 153 is bad
block 154 is bad
block 213 is bad
block 215 is bad
yaffs_read_super: isCheckpointed 0
VFS: Mounted root (yaffs filesystem) on device 31:2.
Freeing init memory: 240K
Warning: unable to open an initial console.
Failed to execute /linuxrc.  Attempting defaults...
Kernel panic - not syncing: No init found.  Try passing init= option to kernel.
Backtrace:
[<c0048fd4>] (dump_backtrace+0x0/0x10c) from [<c0349710>] (dump_stack+0x18/0x1c)
r7:00000000 r6:c04b7d40 r5:c04b7700 r4:c0480248
[<c03496f8>] (dump_stack+0x0/0x1c) from [<c0349760>] (panic+0x4c/0x124)
[<c0349714>] (panic+0x0/0x124) from [<c00444f0>] (init_post+0xec/0x178)
r3:00000000 r2:c388be00 r1:c04ee000 r0:c0411a8c
[<c0044404>] (init_post+0x0/0x178) from [<c000847c>] (kernel_init+0xcc/0xf4)
r5:c001ec40 r4:c001f05c
[<c00083b0>] (kernel_init+0x0/0xf4) from [<c0059f30>] (do_exit+0x0/0x620)
r7:00000000 r6:00000000 r5:00000000 r4:00000000

http://www.armbbs.net/forum.php? ... 4%BC%FE%CF%B5%CD%B3

lz好长的内容啊

问题补充：我在linux环境下解压了天嵌提供的yaffs文件系统源码包root_qtopia_2.2.0_2.6.30.4_20100601.tar，然后使用命令#mkyaffsimage root_qtopia_2.2.0_2.6.30.4_20100601 root_qtopia_2.2.0_2.6.30.4_20100601.bin生成文件镜像，烧入开发板，结果显示的串口信息还是和上面的一样。

一路走过 发表于 2012-5-12 22:32
问题补充：我在linux环境下解压了天嵌提供的yaffs文件系统源码包root_qtopia_2.2.0_2.6.30.4_20100601.tar， ...

你的问题应该是配置有问题，你按着附录5配置一遍，切记不要只看红颜色的部分，黑颜色的也要看，因为黑颜色部分有一条也是添加yaffs2的支持的。你上面所说便证明了这一点，天嵌公司的源码本身是没问题的，因为你没有配置对所以导致错误，代码应该是正确的，希望能帮到你！！！！

~悟`~念~ 发表于 2012-5-13 21:30
你的问题应该是配置有问题，你按着附录5配置一遍，切记不要只看红颜色的部分，黑颜色的也要看，因为黑颜 ...

嗯，谢谢你，重新配置了一遍，问题解决了。

一路走过 发表于 2012-5-14 15:57
嗯，谢谢你，重新配置了一遍，问题解决了。

你这比我走运了，我那会儿论坛问了很多，也没有人能给我解决，我后来连红帽都重装了，还是不行，最后才发现是这里的毛病，“吃得苦中苦，方为人上人啊！”呵呵！！！加油！！！

~悟`~念~ 发表于 2012-5-14 20:06
你这比我走运了，我那会儿论坛问了很多，也没有人能给我解决，我后来连红帽都重装了，还是不行，最后才 ...

嗯，多谢你们这些热心人的帮助啊，少走了不少远路。

一路走过 发表于 2012-5-20 15:15
嗯，多谢你们这些热心人的帮助啊，少走了不少远路。

奇怪了 我和你是一样的版本 我将天嵌提供的yaffs源码 在linux下解压后直接生成镜像 就能用了（用我的yaffs配合其它出厂镜像 正常） 你的居然还要该配置··············

不过我在移植内核的时候倒是遇到了和你一样的问题······哎············
http://bbs.embedsky.net/forum.ph ... hlight=%D2%C6%D6%B2

我也出问题了~

一路走过 发表于 2012-5-20 15:15
嗯，多谢你们这些热心人的帮助啊，少走了不少远路。

请问你是如何解决问题的？是重新配置内核还是busybox?
我使用天嵌出厂的内核，自己编译的文件系统也遇到类似问题，按道理来说出厂的内核应该没问题才对啊。但我看~悟`~念~提醒的查看附录5，就是内核配置啊。
期待你的回复。