linux系统烧完启动不了

##### EmbedSky BIOS for SKY2440/TQ2440 #####
Press Space key to Download Mode !

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 9

##### Erase Nand Menu #####
[1] Nand scrub - really clean NAND erasing bad blocks (UNSAFE)
[2] Nand earse - clean NAND eraseing
[q] Return main Menu
Enter your selection: 1

NAND scrub: device 0 whole chip
Warning: scrub option will erase all factory set bad blocks!
         There is no reliable way to recover them.
         Use this command only for testing purposes if you
         are sure of what you are doing!

Really scrub this NAND flash? <y/N> : y
Erasing at 0xffe0000 -- 100% complete.
OK

##### Erase Nand Menu #####
[1] Nand scrub - really clean NAND erasing bad blocks (UNSAFE)
[2] Nand earse - clean NAND eraseing
[q] Return main Menu
Enter your selection: q

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 1
USB host is connected. Waiting a download.

Now, Downloading [ADDRESS:30000000h,TOTAL:219130]
RECEIVED FILE SIZE:  219130 (213KB/S, 1S)

NAND erase: device 0 offset 0x0, size 0x40000
Erasing at 0x20000 -- 100% complete.
OK

NAND write: device 0 offset 0x0, size 0x357f0

Writing data at 0x35000 -- 100% complete.
219120 bytes written: OK

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 3
USB host is connected. Waiting a download.

Now, Downloading [ADDRESS:30000000h,TOTAL:2305446]
RECEIVED FILE SIZE: 2305446 (750KB/S, 3S)

NAND erase: device 0 offset 0x200000, size 0x200000
Erasing at 0x3e0000 -- 100% complete.
OK

NAND write: device 0 offset 0x200000, size 0x200000

Writing data at 0x3ff800 -- 100% complete.
2097152 bytes written: OK

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 6
USB host is connected. Waiting a download.

Now, Downloading [ADDRESS:30000000h,TOTAL:53632138]
RECEIVED FILE SIZE:53632138 (662KB/S, 79S)

NAND erase: device 0 offset 0x400000, size 0xfc00000
Erasing at 0xffe0000 -- 100% complete.
OK

NAND write: device 0 offset 0x400000, size 0x3325c80

Writing data at 0x35b8800 -- 100% complete.
53632128 bytes written: OK

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: b
USB host is connected. Waiting a download.

Now, Downloading [ADDRESS:30000000h,TOTAL:153610]
RECEIVED FILE SIZE:  153610 (150KB/S, 1S)

NAND erase: device 0 offset 0x100000, size 0x100000
Erasing at 0x1e0000 -- 100% complete.
OK

NAND write: device 0 offset 0x100000, size 0x25800

Writing data at 0x125000 -- 100% complete.
153600 bytes written: OK

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 8
Start Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00200000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
data abort
pc : [<3000b420>]    lr : [<0000005c>]
sp : 302441c4  ip : 7cebcd3c  fp : 302441e0
r10: 40000000  r9 : 30000000  r8 : 30008000
r7 : 051b8919  r6 : e861e409  r5 : 921dbf65  r4 : 3023ad20
r3 : 000000a8  r2 : 302541e4  r1 : 302441e4  r0 : 302541e4
Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

*** Warning - bad CRC or NAND, using default environment

这是全过程，弄了好几遍还是这样。

好，我在试试看。先谢了！！

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 9

##### Erase Nand Menu #####
[1] Nand scrub - really clean NAND erasing bad blocks (UNSAFE)
[2] Nand earse - clean NAND eraseing
[q] Return main Menu
Enter your selection: 1

NAND scrub: device 0 whole chip
Warning: scrub option will erase all factory set bad blocks!
         There is no reliable way to recover them.
         Use this command only for testing purposes if you
         are sure of what you are doing!

Really scrub this NAND flash? <y/N> : y
Erasing at 0xffe0000 -- 100% complete.
OK

##### Erase Nand Menu #####
[1] Nand scrub - really clean NAND erasing bad blocks (UNSAFE)
[2] Nand earse - clean NAND eraseing
[q] Return main Menu
Enter your selection: 2
Start address: 0
Size(eg. 4000000, 0x4000000, 64m and so on): 4000000

NAND erase: device 0 offset 0x0, size 0x4000000
Erasing at 0x3fe0000 -- 100% complete.
OK

##### Erase Nand Menu #####
[1] Nand scrub - really clean NAND erasing bad blocks (UNSAFE)
[2] Nand earse - clean NAND eraseing
[q] Return main Menu
Enter your selection: q

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 1
USB host is connected. Waiting a download.

Now, Downloading [ADDRESS:30000000h,TOTAL:219130]
RECEIVED FILE SIZE:  219130 (213KB/S, 1S)

NAND erase: device 0 offset 0x0, size 0x40000
Erasing at 0x20000 -- 100% complete.
OK

NAND write: device 0 offset 0x0, size 0x357f0

Writing data at 0x35000 -- 100% complete.
219120 bytes written: OK

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 3
USB host is connected. Waiting a download.

Now, Downloading [ADDRESS:30000000h,TOTAL:2305446]
RECEIVED FILE SIZE: 2305446 (750KB/S, 3S)

NAND erase: device 0 offset 0x200000, size 0x200000
Erasing at 0x3e0000 -- 100% complete.
OK

NAND write: device 0 offset 0x200000, size 0x200000

Writing data at 0x3ff800 -- 100% complete.
2097152 bytes written: OK

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 6
USB host is connected. Waiting a download.

Now, Downloading [ADDRESS:30000000h,TOTAL:53632138]
RECEIVED FILE SIZE:53632138 (662KB/S, 79S)

NAND erase: device 0 offset 0x400000, size 0xfc00000
Erasing at 0xffe0000 -- 100% complete.
OK

NAND write: device 0 offset 0x400000, size 0x3325c80

Writing data at 0x35b8800 -- 100% complete.
53632128 bytes written: OK

#####    Boot for Nor Flash Main Menu   #####
[1] Download u-boot or STEPLDR.nb1 or other bootloader to Nand Flash
[2] Download Eboot to Nand Flash
[3] Download Linux Kernel to Nand Flash
[5] Download CRAMFS image to Nand Flash
[6] Download YAFFS image to Nand Flash
[7] Download Program (uCOS-II or TQ2440_Test) to SDRAM and Run it
[8] Boot the system
[9] Format the Nand Flash
[0] Set the boot parameters
[a] Download User Program (eg: uCOS-II or TQ2440_Test)
[b] Download LOGO Picture (.bin) to Nand  Flash
[l] Set LCD Parameters
[o] Download u-boot to Nor Flash
[r] Reboot u-boot
[t] Test Linux Image (zImage)
[q] quit from menu
Enter your selection: 8
Start Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00200000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
data abort
pc : [<3000b420>]    lr : [<0000005c>]
sp : 302441c4  ip : 7cebcd3c  fp : 302441e0
r10: 40000000  r9 : 30000000  r8 : 30008000
r7 : 051b8919  r6 : e861e409  r5 : 921dbf65  r4 : 3023ad20
r3 : 000000a8  r2 : 302541e4  r1 : 302441e4  r0 : 302541e4
Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

*** Warning - bad CRC or NAND, using default environment

还是不好使，我又试了两遍，我查了nand256M也是对应着烧的，烧的镜像是10年的从论坛上下的。

4# zhjun5337


b选项你有烧录吗?没有logo 的话开机会卡住喔
8选项我是没用过，我目前只做b.1.3.6 就能开机了

5# xbirca
logo我也烧过，但是一启动就是闪，然后就进不去了。

你的内核镜像大于了2MB，你需要下载6月份的光盘，它的uboot支持3MB的内核镜像。

7# 亚瑟王
我烧的镜像都是最新的。就是天嵌3.5那里的镜像。

uboot是最新的吗？

9# 亚瑟王

就是天嵌3.5那里一起的Uboot。今天我烧了下光盘里带的09年的就好使，不知道为什么。我烧的10年的都是论坛里最新的镜像。

你把uboot和内核等全套都换成201006版本的，然后你再烧写。