|
本帖最后由 effendi 于 2010-9-15 16:08 编辑
从这行到最后:
usbcore: registered new device driver usb
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 97 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
yaffs Aug 31 2010 19:45:05 Installing.
msgmni has been set to 119
alg: No test for stdrng (krng)
io scheduler noop registered (default)
Console: switching to colour frame buffer device 40x15
fb0: s3c2410fb frame buffer device
backlight initialized
GPIO-Control initialized
PWM-Test initialized
s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
dm9000 Ethernet Driver, V1.31
Now use the default MAC address: 10:23:45:67:89:ab
eth0 (dm9000): not using net_device_ops yet
eth0: dm9000e at c4810000,c4814004 IRQ 51 MAC: 10:23:45:67:89:ab (EmbedSky)
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=3, 30ns Twrph0=7 70ns, Twrph1=3 30ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 1031 at 0x0000080e0000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000400000 : "EmbedSky_Board_kernel"
0x000000400000-0x00000ff80000 : "EmbedSky_Board_yaffs2"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.30.4-EmbedSky ohci_hcd
usb usb1: SerialNumber: s3c24xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
s3c2410_udc: debugfs dir creation failed -19
s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
zc0301: V4L2 driver for ZC0301[P] Image Processor and Control Chip v1:1.10
usbcore: registered new interface driver zc0301
gspca: main v2.5.0 registered
usbcore: registered new interface driver zc3xx
zc3xx: registered
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: powered down.
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
ALSA device list:
#0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2000-02-23 04:24:05 UTC (951279845)
uncorrectable error : <3>end_request: I/O error, dev mtdblock2, sector 0
FAT: unable to read boot sector
VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00 256 mtdblock0 (driver?)
1f01 2048 mtdblock1 (driver?)
1f02 257536 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
Backtrace:
[<c0039fd4>] (dump_backtrace+0x0/0x10c) from [<c02b0f14>] (dump_stack+0x18/0x1c)
r7:c380a0cb r6:c03bbd00 r5:c380a000 r4:c381df40
[<c02b0efc>] (dump_stack+0x0/0x1c) from [<c02b0f64>] (panic+0x4c/0x124)
[<c02b0f18>] (panic+0x0/0x124) from [<c0008e30>] (mount_block_root+0x178/0x234)
r3:00000000 r2:c3831e6c r1:c381df40 r0:c033ebf8
[<c0008cb8>] (mount_block_root+0x0/0x234) from [<c0008f9c>] (mount_root+0xb0/0xf4)
[<c0008eec>] (mount_root+0x0/0xf4) from [<c00090d8>] (prepare_namespace+0xf8/0x18c)
r7:c03bb6e4 r6:c001e83c r5:c001e83c r4:c001e84c
[<c0008fe0>] (prepare_namespace+0x0/0x18c) from [<c0008478>] (kernel_init+0xc8/0xf4)
r7:00000000 r6:c001d70c r5:c001d3b0 r4:c001d70c
[<c00083b0>] (kernel_init+0x0/0xf4) from [<c004af30>] (do_exit+0x0/0x620)
r7:00000000 r6:00000000 r5:00000000 r4:00000000 |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册
x
|