qt2440 配置无线网卡出错，求高手指点

无线网卡类型 TL-WN322G+ v2.0
我按照天嵌科技出品-Linux移植之Step By Step_V4.5_20100605 中关于无线网卡的说明进行配置。报错。无法使用无线网卡。求高手指点迷津。
插入无线网卡后显示
usb 1-1: new full speed USB device using s3c2410-ohci and address 3
usb 1-1: New USB device found, idVendor=0cf3, idProduct=1006
usb 1-1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
usb 1-1: Product: USB2.0 WLAN
usb 1-1: Manufacturer: ATHEROS
usb 1-1: SerialNumber: 12345
usb 1-1: configuration #1 chosen from 1 choice

运行net_set后显示
[root@EmbedSky /etc]# net_set
Try to bring eth0 interface up ...
ifconfig: SIOCSIFADDR: No such device
ifconfig wlan0 192.168.1.4 netmask 255.255.255.0 up
route: SIOCADDRT: Network is unreachable
route add default gw 192.168.1.1
Error for wireless request "Set ESSID" (8B1A) :
    SET failed on device wlan0 ; No such device.
iwconfig wlan0 essid aydongjing key 1234567890
Done

运行ifconfig显示
[root@EmbedSky /etc]# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 10:23:45:67:89:AB  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:51 Base address:0x4000

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

1# aydongjing

route: SIOCADDRT: Network is unreachable

没法链接你的路由。
这个无线网卡需要连接路由的，它不是自动连接。
你看看用户手册的 Linux实验那里，网络设置。
qtopia的界面网络设置中要设置好你的路由登录要求

首先感谢版主答疑，我原来做javaweb的刚接触嵌入式，所以比较外行，别介意我的问题没技术含量。
板子的系统是买的时候自带的。我没有烧写过。
我想问。
1、您说的路由是那个，能不能具体点。
2、qtopia的界面网络设置中wifi部分是灰色的不能编辑
3、我前几天测试时，插入网线可以访问网络
下面是具体的配置
net.conf
IPADDR=192.168.1.4
NETMASK=255.255.255.0
GATEWAY=192.168.1.1
MAC=10:23:45:67:89:ab

nettype.conf
CDMAUSE=0
NETTYPE=2

resolv.conf
nameserver 123.127.160.127

wifi.conf
NETNAME=aydongjing
PASSWORD=1234567890

3# aydongjing


看看手册的 5.1.12 和 5.1.23章节的内容一下

按照5.1.12 网络设置实验来做的
5.1.23 也按照做了 打印信息如下，qt也是读那些配置文件来的参数
Try to bring eth0 interface up ...
ifconfig wlan0 192.168.1.4 netmask 255.255.255.0 up
route add default gw 192.168.1.1
iwconfig wlan0 essid aydongjing key 1234567890
Done
还是不知道那里有问题郁闷

开机打印的信息如下：

*** Warning - bad CRC or NAND, using default environment
##### EmbedSky BIOS for SKY2440/TQ2440 #####
Press Space key to Download Mode !
Booting Linux ...
Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00300000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
Uncompressing Linux........................................................................................................................................................ done, booting the kernel.
Linux version 2.6.30.4-EmbedSky (root@EmbedSky) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #7 Mon May 31 10:56:58 CST 2010
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: TQ2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
NR_IRQS:85
irq: clearing pending ext status 00080000
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 59896KB available (4340K code, 448K data, 188K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 296 bytes
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 97 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
yaffs May 31 2010 10:39:00 Installing.
msgmni has been set to 117
alg: No test for stdrng (krng)
io scheduler noop registered (default)
Console: switching to colour frame buffer device 40x15
fb0: s3c2410fb frame buffer device
backlight initialized
GPIO-Control initialized
PWM-Test initialized
adc initialized
s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
dm9000 Ethernet Driver, V1.31
Now use the default MAC address: 10:23:45:67:89:ab
eth0 (dm9000): not using net_device_ops yet
eth0: dm9000e at c4814000,c4818004 IRQ 51 MAC: 10:23:45:67:89:ab (EmbedSky)
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 174 at 0x0000015c0000
Bad eraseblock 503 at 0x000003ee0000
Bad eraseblock 531 at 0x000004260000
Bad eraseblock 669 at 0x0000053a0000
Bad eraseblock 886 at 0x000006ec0000
Bad eraseblock 1569 at 0x00000c420000
Bad eraseblock 1703 at 0x00000d4e0000
Bad eraseblock 1884 at 0x00000eb80000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000500000 : "EmbedSky_Board_kernel"
0x000000500000-0x000010000000 : "EmbedSky_Board_yaffs2"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.30.4-EmbedSky ohci_hcd
usb usb1: SerialNumber: s3c24xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
s3c2410_udc: debugfs dir creation failed -19
s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
mice: PS/2 mouse device common for all mice
TQ2440 TouchScreen successfully loaded
input: TQ2440 TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
cx231xx v4l2 driver loaded.
usbcore: registered new interface driver cx231xx
usbcore: registered new interface driver usbvision
USBVision USB Video Device Driver for Linux : 0.9.10
usbcore: registered new interface driver ov511
ov511: v1.64 for Linux 2.5:ov511 USB Camera Driver
SE401 usb camera driver version 0.24 registering
usbcore: registered new interface driver se401
usbcore: registered new interface driver stv680
stv680 [usb_stv680_init:1550]
STV(i): usb camera driver version v0.25 registering<6>stv680: v0.25:STV0680 USB Camera Driver
w9968cf: V4L driver for W996[87]CF JPEG USB Dual Mode Camera Chip 1:1.34-basic
usbcore: registered new interface driver w9968cf
usbcore: registered new interface driver zr364xx
zr364xx: Zoran 364xx
usbcore: registered new interface driver stkwebcam
sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.47pre49
usbcore: registered new interface driver sn9c102

et61x251: V4L2 driver for ET61X[12]51 PC Camera Controllers v1:1.09
usbcore: registered new interface driver et61x251
pwc: Philips webcam module version 10.0.13 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
usbcore: registered new interface driver Philips webcam
zc0301: V4L2 driver for ZC0301[P] Image Processor and Control Chip v1:1.10
usbcore: registered new interface driver zc0301
gspca: main v2.5.0 registered
usbcore: registered new interface driver conex
conex: registered
usbcore: registered new interface driver etoms
etoms: registered
usbcore: registered new interface driver finepix
finepix: registered
usbcore: registered new interface driver mars
mars: registered
usbcore: registered new interface driver mr97310a
mr97310a: registered
usbcore: registered new interface driver ov519
ov519: registered
usbcore: registered new interface driver pac207
pac207: registered
usbcore: registered new interface driver pac7311
pac7311: registered
usbcore: registered new interface driver sonixb
sonixb: registered
usbcore: registered new interface driver sonixj
sonixj: registered
usbcore: registered new interface driver spca500
spca500: registered
usbcore: registered new interface driver spca501
spca501: registered
usbcore: registered new interface driver spca505
spca505: registered
usbcore: registered new interface driver spca506
spca506: registered
usbcore: registered new interface driver spca508
spca508: registered
usbcore: registered new interface driver spca561
spca561: registered
usbcore: registered new interface driver sq905
sq905: registered
usbcore: registered new interface driver sq905c
sq905c: registered
usbcore: registered new interface driver sunplus
sunplus: registered
usbcore: registered new interface driver stk014
stk014: registered
usb 1-1: new full speed USB device using s3c2410-ohci and address 2
usbcore: registered new interface driver t613
t613: registered
usbcore: registered new interface driver tv8532
tv8532: registered
usbcore: registered new interface driver vc032x
vc032x: registered
usbcore: registered new interface driver zc3xx
zc3xx: registered
usbcore: registered new interface driver ALi m5602
ALi m5602: registered
usbcore: registered new interface driver STV06xx
STV06xx: registered
usbcore: registered new interface driver ibmcam
usbcore: registered new interface driver ultracam
konicawc: v1.4:Konica Webcam driver
usbcore: registered new interface driver konicawc
usbcore: registered new interface driver vicam
quickcam_messenger: v0.01:Logitech Quickcam Messenger USB
usbcore: registered new interface driver QCM
usbcore: registered new interface driver s2255
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: starting watchdog timer
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq enabled
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: powered down.
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
usb 1-1: New USB device found, idVendor=0cf3, idProduct=1006
usb 1-1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
usb 1-1: Product: USB2.0 WLAN
usb 1-1: Manufacturer: ATHEROS
usb 1-1: SerialNumber: 12345
usb 1-1: configuration #1 chosen from 1 choice
ALSA device list:
  #0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
s3c2410-rtc s3c2410-rtc: setting system clock to 2011-03-03 12:49:41 UTC (1299156581)
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
block 135 is bad
block 464 is bad
block 492 is bad
block 630 is bad
block 847 is bad
block 1530 is bad
block 1664 is bad
block 1845 is bad
yaffs_read_super: isCheckpointed 0
VFS: Mounted root (yaffs filesystem) on device 31:2.
Freeing init memory: 188K
Start Qtopia-2.2.0
usbcore: registered new interface driver rt73usb
usbcore: registered new interface driver zd1211rw
initializing s3c2440 camera interface......
s3c2440 camif init done
Loading OV9650 driver.........
OV9650 address 0x60, manufacture ID 0xFFFF, expect 0x7FA2
OV9650 address 0x60, manufacture ID 0xFFFF, expect 0x7FA2
No OV9650 found!!!
Try to bring eth0 interface up ...
ifconfig: SIOCSIFADDR: No such device
ifconfig wlan0 192.168.1.4 netmask 255.255.255.0 up
route: SIOCADDRT: Network is unreachable
route add default gw 192.168.1.1
Error for wireless request "Set ESSID" (8B1A) :
    SET failed on device wlan0 ; No such device.
iwconfig wlan0 essid aydongjing key 1234567890
Done
[03/Mar/2011:04:49:48 +0000] boa: server version Boa/0.94.13
[03/Mar/2011:04:49:48 +0000] boa: server built Jul 29 2009 at 14:27:34.
[03/Mar/2011:04:49:48 +0000] boa: starting server pid=639, port 80

Please press Enter to activate this console.