想烧个PDA的文件镜像,选的是256M的那个
结果烧写后打到nand那边启动确是卡在开机logo就没反应了,连接终端后显示串口信息大体如下,请问是什么原因呢
Enter your selection: 6 USB host is connected. Waiting a download. 准备下载文件: E:\TQ2440资料\TQ2440资料\TQ2440_CD\出厂烧录镜像合集\Linux文件系统镜像\root_TQ2440_PDA_256MB_20121214.bin ) S3C24XX NAND Driver, (c) 2004 Simtec Electronics s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit) NAND_ECC_NONE selected by board driver. This is not recommended !! Scanning device for bad blocks Bad eraseblock 579 at 0x000004860000 Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x000000000000-0x000000040000 : "EmbedSky_Board_uboot" 0x000000200000-0x000000500000 : "EmbedSky_Board_kernel" 0x000000500000-0x000010000000 : "EmbedSky_Board_yaffs2" ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver s3c2410-ohci s3c2410-ohci: S3C24XX OHCI s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: S3C24XX OHCI usb usb1: Manufacturer: Linux 2.6.30.4-EmbedSky ohci_hcd usb usb1: SerialNumber: s3c24xx usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial usbserial: USB Serial Driver core USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 pl2303: Prolific PL2303 USB to serial adaptor driver s3c2410_udc: debugfs dir creation failed -19 s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes mice: PS/2 mouse device common for all mice TQ2440 TouchScreen successfully loaded input: TQ2440 TouchScreen as /devices/virtual/input/input0 S3C24XX RTC, (c) 2004,2006 Simtec Electronics s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0 i2c /dev entries driver Linux video capture interface: v2.00 cx231xx v4l2 driver loaded. usbcore: registered new interface driver cx231xx usbcore: registered new interface driver usbvision USBVision USB Video Device Driver for Linux : 0.9.10 usbcore: registered new interface driver ov511 ov511: v1.64 for Linux 2.5:ov511 USB Camera Driver SE401 usb camera driver version 0.24 registering usbcore: registered new interface driver se401 usbcore: registered new interface driver stv680 stv680 sb_stv680_init:1550] STV(i): usb camera driver version v0.25 registering<6>stv680: v0.25:STV0680 USB Camera Driver w9968cf: V4L driver for W996[87]CF JPEG USB Dual Mode Camera Chip 1:1.34-basic usbcore: registered new interface driver w9968cf usbcore: registered new interface driver zr364xx zr364xx: Zoran 364xx usbcore: registered new interface driver stkwebcam sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.47pre49 usbcore: registered new interface driver sn9c102 et61x251: V4L2 driver for ET61X[12]51 PC Camera Controllers v1:1.09 usbcore: registered new interface driver et61x251 pwc: Philips webcam module version 10.0.13 loaded. pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840. pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30, pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100. usbcore: registered new interface driver Philips webcam zc0301: V4L2 driver for ZC0301[P] Image Processor and Control Chip v1:1.10 usbcore: registered new interface driver zc0301 gspca: main v2.5.0 registered
|