|
本帖最后由 NeroDevil 于 2013-8-13 01:26 编辑
TQ2440装自带光盘里的wince,按视频里的方法安装,linux的可以安装使用,win测的安装到最后一 步,安装文件系统时,DNW软件显示进度条过半之后,cecureCRT软件就报错了。如下所示,求解,板子刚买的。
Microsoft Windows CE Bootloader for TQ2440/SKY2440 Version 6.0 Built Jun 12 2010
Press [ENTER] to launch image stored on boot media, or [SPACE] to enter boot monitor.
Initiating image launch in 1 seconds.
Ethernet Boot Loader Configuration:
0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now
Enter your selection: b
Reserving Blocks [0x0 - 0xf] ...
...reserve complete.
Ethernet Boot Loader Configuration:
0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now
Enter your selection: 9
Enter TQ2440 FastLowLevelFormat [0x10, 0x7ff].
Format TQ2440 Nand Flash: found a bad block (0x3d2) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x4d7) - skipping...
Format TQ2440 Nand Flash: found a bad block (0x5cc) - skipping...
Format TQ2440 Nand Flash: ...erase complete.
WriteMBR: MBR block = 0x10.
BP_FastLowLevelFormat: Done.
Ethernet Boot Loader Configuration:
0) IP address: 192.168.1.6
1) Subnet mask: 255.255.255.0
2) DHCP: Disabled
3) Boot delay: 1 seconds
4) Reset to factory default configuration
5) Startup image: LAUNCH EXISTING
6) Program disk image into SmartMedia card: Enabled
7) Program DM9000 MAC address (10:23:45:67:89:AB)
8) Kernel Debugger: ENABLED
9) Format Boot Media for BinFS
B) Mark Bad Block at Reserved Block
D) Download image now(USE TFTP)
E) Erase Reserved Block
F) Low-level format the Smart Media card
L) LAUNCH existing Boot Media image
R) Read Configuration
U) Download image now(USE USB)
W) Write Configuration Right Now
Enter your selection: u
USB host is connected. Waiting a download.
Addr: 0xC000000 ; Size: 0x1ED2BA5
Read Bin Files StartAddr:0x80200000 ; Length: 0x1F44084
Download BIN file information:
-----------------------------------------------------
[0]: Base Address=0x80200000 Length=0x1f44084
-----------------------------------------------------
+=OEMVerifyMemory+ dwStartAddr:0x80200000 dwLength:0x1f44084
RAM image 0xa 0x82144083
ERROR: Checksum failure (expected=0x1755CCB computed=0x15369BE)
****** Checksum failure on record 154, ABORT!!! ******
|
|