- ##### EmbedSky BIOS for SKY2440/TQ2440 #####
- Press Space key to Download Mode !
- Booting Linux ...
- Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00200000 ... Copy Kernel to SDRAM done,NOW, Booting Linux......
- Uncompressing Linux....................................................................................................... done, booting the kernel.
- Linux version 2.6.25.6 (root@localhost.localdomain) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #12 Tue Sep 28 22:16:11 CST 2010
- CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
- Machine: SMDK2440
- ATAG_INITRD is deprecated; please update your bootloader.
- Memory policy: ECC disabled, Data cache writeback
- CPU S3C2440A (id 0x32440001)
- S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
- S3C24XX Clocks, (c) 2004 Simtec Electronics
- CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
- CPU0: D VIVT write-back cache
- CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
- CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
- irq: clearing pending ext status 00080000
- irq: clearing subpending status 00000002
- PID hash table entries: 256 (order: 8, 1024 bytes)
- timer tcon=00500000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
- Console: colour dummy device 80x30
- console [ttySAC0] enabled
- Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- Memory: 64MB = 64MB total
- Memory: 61568KB available (2900K code, 257K data, 152K init)
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- net_namespace: 152 bytes
- NET: Registered protocol family 16
- S3C2410 Power Management, (c) 2004 Simtec Electronics
- S3C2440: Initialising architecture
- S3C2440: IRQ Support
- S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
- DMA channel 0 at c4800000, irq 33
- DMA channel 1 at c4800040, irq 34
- DMA channel 2 at c4800080, irq 35
- DMA channel 3 at c48000c0, irq 36
- S3C244X: Clock Support, DVS off
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
- TCP: Hash tables configured (established 2048 bind 2048)
- TCP reno registered
- NetWinder Floating Point Emulator V0.97 (double precision)
- yaffs Sep 24 2010 21:52:28 Installing.
- io scheduler noop registered
- io scheduler anticipatory registered (default)
- io scheduler deadline registered
- io scheduler cfq registered
- Console: switching to colour frame buffer device 40x30
- fb0: s3c2410fb frame buffer device
- lp: driver loaded but no devices found
- ppdev: user-space parallel port driver
- Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
- s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
- s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
- s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
- brd: module loaded
- loop: module loaded
- dm9000 Ethernet Driver, V1.30
- Uniform Multi-Platform E-IDE driver
- ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
- Driver 'sd' needs updating - please use bus_type methods
- Driver 'sr' needs updating - please use bus_type methods
- S3C24XX NAND Driver, (c) 2004 Simtec Electronics
- s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns
- NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
- Scanning device for bad blocks
- Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
- 0x00000000-0x00040000 : "Bootloader_Uboot"
- 0x00200000-0x00400000 : "kernel"
- 0x00400000-0x03ff8000 : "yaffs2"
- usbmon: debugfs is not available
- s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
- s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
- s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
- usb usb1: configuration #1 chosen from 1 choice
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 2 ports detected
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- mice: PS/2 mouse device common for all mice
- S3C24XX RTC, (c) 2004,2006 Simtec Electronics
- s3c2440-i2c s3c2440-i2c: slave address 0x10
- s3c2440-i2c s3c2440-i2c: bus frequency set to 390 KHz
- s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
- S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
- s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
- usbcore: registered new interface driver hiddev
- usbcore: registered new interface driver usbhid
- drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
- TCP cubic registered
- NET: Registered protocol family 1
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
- yaffs: dev is 32505858 name is "mtdblock2"
- yaffs: passed flags ""
- yaffs: Attempting MTD mount on 31.2, "mtdblock2"
- yaffs_read_super: isCheckpointed 0
- VFS: Mounted root (yaffs filesystem).
- Freeing init memory: 152K
- mount: mounting tmpfs on /tmp failed: No such file or directory
- mount: mounting tmpfs on /dev failed: Invalid argument
- mount: mounting var on /dev failed: Invalid argument
- mkdir: cannot create directory '/dev/pts': File exists
- /etc/init.d/rcS: line 15: can't create /proc/sys/kenel/hotplug: nonexistent directory
- /etc/init.d/rcS: line 20: net_set: Permission denied
- /etc/init.d/rcS: line 22: /etc/rc.d/init.d/httpd: not found
- [root /]#
- Please press Enter to activate this console. ^C
- [root /]#
复制代码 我的启动过成如上。
lcd就是不显示logo。一片黑。
怎么回事啊。
请教了 |