移植Qtopia遇到问题

终端打印如下，，
mac80211: Unknown symbol cfg80211_scan_done
mac80211: Unknown symbol regulatory_hint_11d
mac80211: Unknown symbol cfg80211_wext_giwscan
mac80211: Unknown symbol cfg80211_wext_giwname
mac80211: Unknown symbol cfg80211_wext_giwmode
mac80211: Unknown symbol cfg80211_wext_giwrange
mac80211: Unknown symbol wiphy_register
mac80211: Unknown symbol wiphy_new
mac80211: Unknown symbol cfg80211_put_bss
mac80211: Unknown symbol cfg80211_hold_bss
mac80211: Unknown symbol cfg80211_send_rx_auth
mac80211: Unknown symbol cfg80211_send_rx_disassoc
mac80211: Unknown symbol wiphy_unregister
mac80211: Unknown symbol ieee80211_radiotap_iterator_init
mac80211: Unknown symbol cfg80211_get_bss
mac80211: Unknown symbol __ieee80211_get_channel
mac80211: Unknown symbol cfg80211_wext_siwmode
mac80211: Unknown symbol cfg80211_send_rx_assoc
mac80211: Unknown symbol ieee80211_radiotap_iterator_next
mac80211: Unknown symbol ieee80211_channel_to_frequency
mac80211: Unknown symbol cfg80211_wext_siwscan
mac80211: Unknown symbol cfg80211_inform_bss_frame
mac80211: Unknown symbol ieee80211_frequency_to_channel
mac80211: Unknown symbol cfg80211_send_rx_deauth
mac80211: Unknown symbol cfg80211_unhold_bss
mac80211: Unknown symbol cfg80211_unlink_bss
mac80211: Unknown symbol wiphy_free
/dev/watchdog: No such file or directory
open fbdevice: No such file or directory
insmod: can't insert '/lib/mac80211.ko': unknown symbol in module, or unknown pa
rameter
rt2x00lib: Unknown symbol ieee80211_register_hw
rt2x00lib: Unknown symbol ieee80211_get_hdrlen_from_skb
rt2x00lib: Unknown symbol ieee80211_wake_queue
rt2x00lib: Unknown symbol ieee80211_tx_status_irqsafe
rt2x00lib: Unknown symbol ieee80211_ctstoself_get
rt2x00lib: Unknown symbol ieee80211_wake_queues
rt2x00lib: Unknown symbol ieee80211_iterate_active_interfaces
rt2x00lib: Unknown symbol ieee80211_stop_queue
rt2x00lib: Unknown symbol ieee80211_stop_queues
rt2x00lib: Unknown symbol ieee80211_iterate_active_interfaces_atomic
rt2x00lib: Unknown symbol ieee80211_channel_to_frequency
rt2x00lib: Unknown symbol ieee80211_unregister_hw
rt2x00lib: Unknown symbol ieee80211_rts_get
rt2x00lib: Unknown symbol ieee80211_beacon_get
rt2x00lib: Unknown symbol ieee80211_rx_irqsafe
insmod: can't insert '/lib/rt2x00lib.ko': unknown symbol in module, or unknown p
arameter
rt2x00usb: Unknown symbol rt2x00lib_probe_dev
rt2x00usb: Unknown symbol ieee80211_free_hw
rt2x00usb: Unknown symbol ieee80211_alloc_hw
rt2x00usb: Unknown symbol rt2x00lib_rxdone
rt2x00usb: Unknown symbol rt2x00lib_remove_dev
rt2x00usb: Unknown symbol rt2x00lib_txdone
rt2x00usb: Unknown symbol rt2x00queue_get_queue
insmod: can't insert '/lib/rt2x00usb.ko': unknown symbol in module, or unknown p
arameter
rt73usb: Unknown symbol rt2x00mac_add_interface
rt73usb: Unknown symbol crc_itu_t_table
rt73usb: Unknown symbol rt2x00mac_get_stats
rt73usb: Unknown symbol rt2x00usb_disable_radio
rt73usb: Unknown symbol rt2x00mac_set_key
rt73usb: Unknown symbol rt2x00usb_vendor_request_buff
rt73usb: Unknown symbol rt2x00usb_vendor_request_large_buff
rt73usb: Unknown symbol rt2x00usb_kick_tx_queue
rt73usb: Unknown symbol rt2x00usb_write_tx_data
rt73usb: Unknown symbol rt2x00mac_config_interface
rt73usb: Unknown symbol rt2x00mac_remove_interface
rt73usb: Unknown symbol rt2x00usb_vendor_request
rt73usb: Unknown symbol rt2x00usb_probe
rt73usb: Unknown symbol rt2x00mac_config
rt73usb: Unknown symbol rt2x00queue_get_queue
rt73usb: Unknown symbol rt2x00usb_clear_entry
rt73usb: Unknown symbol rt2x00mac_conf_tx
rt73usb: Unknown symbol rt2x00mac_start
rt73usb: Unknown symbol rt2x00mac_stop
rt73usb: Unknown symbol rt2x00mac_configure_filter
rt73usb: Unknown symbol rt2x00usb_disconnect
rt73usb: Unknown symbol rt2x00mac_tx
rt73usb: Unknown symbol rt2x00usb_vendor_req_buff_lock
rt73usb: Unknown symbol rt2x00mac_get_tx_stats
rt73usb: Unknown symbol rt2x00usb_regbusy_read
rt73usb: Unknown symbol rt2x00usb_kill_tx_queue
rt73usb: Unknown symbol crc_itu_t
rt73usb: Unknown symbol rt2x00usb_uninitialize
rt73usb: Unknown symbol rt2x00usb_initialize
rt73usb: Unknown symbol rt2x00mac_bss_info_changed
insmod: can't insert '/lib/rt73usb.ko': unknown symbol in module, or unknown par
ameter
zd1211rw: Unknown symbol ieee80211_free_hw
zd1211rw: Unknown symbol ieee80211_alloc_hw
zd1211rw: Unknown symbol regulatory_hint
zd1211rw: Unknown symbol ieee80211_register_hw
zd1211rw: Unknown symbol ieee80211_tx_status_irqsafe
zd1211rw: Unknown symbol ieee80211_wake_queues
zd1211rw: Unknown symbol ieee80211_stop_queues
zd1211rw: Unknown symbol ieee80211_unregister_hw
zd1211rw: Unknown symbol ieee80211_beacon_get
zd1211rw: Unknown symbol ieee80211_rx_irqsafe
insmod: can't insert '/lib/zd1211rw.ko': unknown symbol in module, or unknown pa
rameter
initializing s3c2440 camera interface......
s3c2440 camif init done
Loading OV9650 driver.........
OV9650 address 0x60, manufacture ID 0xFFFF, expect 0x7FA2
OV9650 address 0x60, manufacture ID 0xFFFF, expect 0x7FA2
No OV9650 found!!!
Try to bring eth0 interface up ...
ifconfig eth0 hw ether 10:23:45:67:89:ab
eth0: link down
ifconfig eth0 192.168.1.6 netmask 255.255.255.0 up
add default gw 192.168.1.2
Done
[25/Oct/2010:21:46:14 +0000] boa: server version Boa/0.94.13
[25/Oct/2010:21:46:14 +0000] boa: server built Jul 29 2009 at 14:27:34.
[25/Oct/2010:21:46:14 +0000] boa: starting server pid=993, port 80
这是怎么回事

1# wangpeihui123


我没有看到和你Qtopia多大关联的信息。和你的主题就是Qtopia编译错误。
你这是内核的信息了

这是内核有问题吗，，是什么问题？？？？

Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "EmbedSky_Board_uboot"
0x000000200000-0x000000500000 : "EmbedSky_Board_kernel"
0x000000500000-0x000010000000 : "EmbedSky_Board_yaffs2"
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mice: PS/2 mouse device common for all mice
TQ2440 TouchScreen successfully loaded
input: TQ2440 TouchScreen as /devices/virtual/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
s3c2440-sdi s3c2440-sdi: powered down.
ALSA device list:
  #0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
s3c2410-rtc s3c2410-rtc: setting system clock to 2010-10-26 19:09:47 UTC (128812
0187)
end_request: I/O error, dev mtdblock2, sector 256
isofs_fill_super: bread failed, dev=mtdblock2, iso_blknum=64, block=128
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
block 27 is bad
block 195 is bad
block 776 is bad
block 792 is bad
block 1314 is bad
block 1610 is bad
block 1768 is bad
yaffs_read_super: isCheckpointed 0
VFS: Mounted root (yaffs filesystem) on device 31:2.
Freeing init memory: 108K
Try to bring eth0 interface up ...
ifconfig eth0 hw ether 10:23:45:67:89:ab
eth0: link down
ifconfig eth0 192.168.1.6 netmask 255.255.255.0 up
BusyBox v1.13.0 (2010-10-22 20:06:34 CST) multi-call binary

Usage: route [{add|del|delete}]

Edit kernel routing tables

Options:
        -n      Don't resolve names
        -e      Display other/more information
        -A inet{6}      Select address family

add default gw
Done
[26/Oct/2010:19:09:55 +0000] boa: server version Boa/0.94.13
[26/Oct/2010:19:09:55 +0000] boa: server built Oct 21 2010 at 18:12:37.
[26/Oct/2010:19:09:55 +0000] boa: starting server pid=971, port 80
Start Qtopia-2.2.0
Please press Enter to activate this console.
终端打印信息没有什么错误，，，为什么屏幕是花屏显示不出qtopia

我的qtopia文件内容如下
#!/bin/sh
echo Start Qtopia-2.2.0 > /dev/tq2440_serial0
export set HOME=/root
export set QTDIR=/opt/Qtopia
export set QPEDIR=/opt/Qtopia
export set KDEDIR=/opt/kde
export set QWS_KEYBOARD="TTY:dev/tty1"
if [ -f /sys/devices/virtual/input/input0/uevent ]; then
        export set TSLIB_TSDEVICE=/dev/event0
        export set TSLIB_CONFFILE=/dev/ts.conf
        export set TSLIB_PLUGINDIR=/lib/ts
        export set TSLIB_CALIBFILE=/etc/pointercal
        export set QWS_MOUSE_PROTO="TPanel:/dev/event0 USB:/dev/mouse0"
else
        export set QWS_MOUSE_PROTO="USB:/dev/mouse0"
        if [ -f /etc/pointercal ]; then
                #$QPEDIR/bin/qpe > /dev/null 2>/dev/null
                echo only use mouse >tq2440_serial0
        else
                #ts_calibrate
                #$QPEDIR/bin/qpe > /dev/null 2>/dev/null
                echo "1 0 1 0 1 1 65536" >/etc/pointercal
        fi
fi
export set PATH=$QPEDIR/bin:$PATH
export set LD_LIBRARY_PATH=$QTDIR/lib:$QPEDIR/lib
if [ -f /etc/pointercal ]; then
        qpe 1>/dev/null 2>/dev/null
else
        ts_calibrate
        qpe 1>/dev/null 2>/dev/null
fi

现在qtopia可以启动了，，但是就显示一个启动界面，，，
用手触摸屏幕没有反应，，打印信息如下
ifconfig eth0 hw ether 10:23:45:67:89:ab
eth0: link down
ifconfig eth0 192.168.1.6 netmask 255.255.255.0 up
BusyBox v1.13.0 (2010-10-22 20:06:34 CST) multi-call binary

Usage: route [{add|del|delete}]

Edit kernel routing tables

Options:
        -n      Don't resolve names
        -e      Display other/more information
        -A inet{6}      Select address family

add default gw
Done
[26/Oct/2010:21:45:04 +0000] boa: server version Boa/0.94.13
[26/Oct/2010:21:45:04 +0000] boa: server built Oct 21 2010 at 18:12:37.
[26/Oct/2010:21:45:04 +0000] boa: starting server pid=969, port 80
Start Qtopia-2.2.0

Please press Enter to activate this console. Couldnt open tslib config file: No
such file or directory
ts_config: Illegal seek

这是怎么回事

7# wangpeihui123

Couldnt open tslib config file: Nosuch file or directory
ts_config: Illegal seek

你的 /etc 下面没有  ts.config 这个配置文件。

etc这个目录下面就没有ts.config这个文件，，，光盘提供的文件系统也没有，，，倒是有一个ts.conf这个文件，但是我的文件系统下面有这个文件啊，，，，

9# wangpeihui123


嗯，写错了，不好意识。
就是ts.conf 这个。

已经搞定了，现在qtopia能正常启动了，但是显示不正常，好像经过平移，左边显示大部分（可操作），右边显示小部分（不可操作），这是咋回事？

图片

12# wangpeihui123

可能你的LCD的时序不对了

怎么解决啊，，，，

14# wangpeihui123


烧写一下，天嵌的内核，针对你的LCD的尺寸而烧写。